Whirlpool DHG65SG1CX Instruções de Utilização descarregar pdf (Página 5)

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

! The hob burners do not require primary air adjustment.

! After adjusting the appliance so it may be used

with a different type of gas, replace the old rating

label with a new one that corresponds to the new

type of gas (these labels are available from

Authorised Technical Assistance Centres).

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet hose in

accordance with current national regulations relating

to “regulators for channelled gas”.

Adapting the oven

Replacing the oven burner nozzle

1.open the oven door fully

2.pull out the sliding oven

bottom

3.unscrew the burner fastening

screws

4.remove screw “V” and then

the oven burner.

5.Unscrew the oven burner

nozzle using the special

socket spanner for the

nozzles, or a 7 mm socket

spanner, and replace it with a

nozzle suited to the new type

of gas (see Table 1).

Take particular care

handling the spark plug

wires and the thermocouple

pipes.

6.Replace all the parts,

following the steps described

above in the reverse order..

Adjusting the gas oven burner’s minimum

setting:

1. Light the burner (see Start-up and Use).

2. Turn the knob to the minimum position (MIN) after

it has been in the maximum position (MAX) for

approximately 10 minutes.

3. Remove the knob.

4. Tighten or loosen the adjustment screws on the

outside of the thermostat pin (see figure) until the

flame is small but steady.

! If the appliance is connected to liquid gas, the

adjustment screw must be fastened as tightly as

possible.

5. Turn the knob from the MAX position to the MIN

position quickly or open and shut the oven door,

making sure that the burner is not extinguished.

Replacing the Triple ring burner nozzles

1. Remove the pan supports and lift the burners out of

their housing. The burner consists of two separate

parts (see pictures).

2. Unscrew the nozzles using a 7 mm socket spanner.

Replace the nozzles with models that are configured

for use with the new type of gas (see Table 1). The

two nozzles have the same hole diameter.

3. Replace all the components by completing the above

operations in reverse order.

• Adjusting the burners’ primary air :

Does not require adjusting.

• Setting the burners to minimum:

1. Turn the tap to the low flame position.

2. Remove the knob and adjust the adjustment screw,

which is positioned in or next to the tap pin, until the

flame is small but steady.

3. Having adjusted the flame to the required low setting,

while the burner is alight, quickly change the position

of the knob from minimum to maximum and vice

versa several times, checking that the flame does not

go out.

4. Some appliances have a safety device

(thermocouple) fitted. If the device fails to work when

the burners are set to the low flame setting, increase

this low flame setting using the adjusting screw.

5. Once the adjustment has been made, replace the

seals on the by-passes using sealing wax

! If the appliance is connected to liquid gas, the

regulation screw must be fastened as tightly as

possible.

! Once this procedure is finished, replace the old rating

sticker with one indicating the new type of gas used.

Stickers are available from any of our Service Centres.

! Should the gas pressure used be different (or vary

slightly) from the recommended pressure, a suitable

pressure regulator must be fitted to the inlet pipe (in

order to comply with current national regulations).

1 2 3 4 5 6 7 8 9 10 ... 15 16

Comentários a estes Manuais

Sem comentários

Whirlpool DHG65SG1CX Instruções de Utilização Página 5

Comentários a estes Manuais

Manuais e produtos relacionados com Fogões Whirlpool DHG65SG1CX